Hyper-V

Installing the CTERA Edge Filer in a Hyper-V Environment

Installing the CTERA Edge Filer involves creating and configuring a virtual machine and then performing an initial configuration, described in First Time Setup.

The edge filer can be installed in a Microsoft Hyper-V environment:

• Hyper-V for Windows Servers 2016 and higher.
• Access to the *.vhd file from the Hyper-V Manager

Contact CTERA, and request the latest VHD gateway disk image.

To install the CTERA Edge Filer in a Hyper-V environment:

1. Open the Hyper-V Manager.
2. Right-click the hypervisor and click New > Virtual Machine.
   
   The New Virtual Machine Wizard opens, displaying the Before You Begin or the Specify Name and Location window.
   
3. If the Before You Begin window is displayed, click Next.
   The Specify Name and Location window is displayed.
   
4. Enter a name for the portal and click Next.
   The Specify Generation window is displayed.
   
5. Leave the Generation 1 type virtual machine and click Next.
   The Assign Memory window is displayed.
   
6. Specify the RAM for the machine.
7. Make sure Use Dynamic Memory for this virtual machine is unchecked.
8. Click Next.
   The Configure Networking window is displayed.
   
9. Select the network from the Connection drop-down list and click Next.
   The Connect Virtual Hard Disk window is displayed.
   
10. Select the Use an existing virtual hard disk option and browse to the vhd file from CTERA.
    
11. Click Next.
    The Completing the New Virtual Machine Wizard window is displayed.
12. Click Finish.
13. Click Settings.
    
    1. Optionally, select Memory in the Hardware list and change the RAM value, based on the edge filer requirements.
    2. Click Apply.
    3. Optionally, select Processor in the Hardware list and change the Number of virtual processors value, based on the edge filer requirements.
    4. Click Apply.
    5. Select Hard Drive under SCSI Controller in the Hardware list for a new hard drive.
       
    6. Click New.
       The New Virtual Hard Disk Wizard is displayed.
       
    7. Click Next and make sure the Dynamically expanding disk type is selected.
       
    8. Click Next and specify a name and location for the disk.
    9. Click Next and configure the disk.
       
    10. Specify the disk size. CTERA recommends storage of at least 20% of the CTERA Portal Global Name Space. The maximum storage is dependent on the license.
        • For an EV16 license, the maximum is 16TB.
        • For an EV32 license, the maximum is 32TB.
        • For an EV64 license, the maximum is 64TB.
        • For an EV128 license, the maximum is 128TB.
        • For an EV256 license, the maximum is 256TB.
        Note

        CTERA recommends that the maximum storage is defined as a single disk. A Microsoft Hyper-V host limits disks to a maximum of 64TB. To support storage greater than 64TB, you need to create multiple disks, each less than 64TB, and then create a volume combining the disks in the HCP Anywhere Enterprise Edge Filer user interface.

    11. Click Next and then Finish.
    12. Click Apply and then OK.
14. Right-click the virtual machine and click Start.

To get the virtual machine IP address:

1. Access the virtual machine.
   The following login screen is displayed:
   
2. Login in with the username setup and no password, as instructed.
   Using DHCP, after a few seconds the IP address to access the CTERA Edge Filer in a browser is displayed in the top right of the console.
   

To set a static IP address:

1. Access the virtual machine.
   The following login screen is displayed:
   
2. Login in with the username setup and no password, as instructed.
   The console is displayed.
   
3. Click in the console to transfer the keyboard control to the console and, if necessary, use the arrow keys to scroll to Network settings.
4. Press Enter.
   
5. Select Static IP mode and press OK.
6. Complete the configuration for static mode by entering the static IP, netmask, default CTERA Edge Filer IP and the primary and secondary DNS server IPs.
7. Press OK.